Home Home > GIT Browse
summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2016-02-07 15:23:20 -0800
committerLinus Torvalds <torvalds@linux-foundation.org>2016-02-07 15:23:20 -0800
commitc17dfb019d52d933a595778d085f83d2b3b34edb (patch)
tree5dd55679d587e57d830a0d8f65c73cacda488591
parent63fee123da6a05b48695599c4349ab5de97da5e2 (diff)
parent381a65c21aa1fcf4f3fafe70027b79b303bdb71d (diff)
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson: "The first real batch of fixes for this release cycle, so there are a few more than usual. Most of these are fixes and tweaks to board support (DT bugfixes, etc). I've also picked up a couple of small cleanups that seemed innocent enough that there was little reason to wait (const/ __initconst and Kconfig deps). Quite a bit of the changes on OMAP were due to fixes to no longer write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but there were also other fixes. Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC fixes on OMAP5, and Nomadik had changes to MMC parameters in DT. All in all, mostly the usual mix of various fixes" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits) ARM: multi_v7_defconfig: enable DW_WATCHDOG ARM: nomadik: fix up SD/MMC DT settings ARM64: tegra: Add chosen node for tegra132 norrin ARM: realview: use "depends on" instead of "if" after prompt ARM: tango: use "depends on" instead of "if" after prompt ARM: tango: use const and __initconst for smp_operations ARM: realview: use const and __initconst for smp_operations bus: uniphier-system-bus: revive tristate prompt arm64: dts: Add missing DMA Abort interrupt to Juno bus: vexpress-config: Add missing of_node_put ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2 ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address ARM: dts: LogicPD Torpedo: Revert Duplicative Entries ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types ARM: dts: am4372: fix irq type for arm twd and global timer ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type ...
-rw-r--r--arch/arm/boot/dts/am33xx.dtsi1
-rw-r--r--arch/arm/boot/dts/am4372.dtsi5
-rw-r--r--arch/arm/boot/dts/am437x-gp-evm.dts4
-rw-r--r--arch/arm/boot/dts/am43x-epos-evm.dts2
-rw-r--r--arch/arm/boot/dts/am57xx-cl-som-am57x.dts12
-rw-r--r--arch/arm/boot/dts/am57xx-sbc-am57x.dts8
-rw-r--r--arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts1
-rw-r--r--arch/arm/boot/dts/at91-sama5d2_xplained.dts12
-rw-r--r--arch/arm/boot/dts/at91-sama5d4_xplained.dts8
-rw-r--r--arch/arm/boot/dts/at91-sama5d4ek.dts11
-rw-r--r--arch/arm/boot/dts/at91sam9n12ek.dts2
-rw-r--r--arch/arm/boot/dts/kirkwood-lswvl.dts25
-rw-r--r--arch/arm/boot/dts/kirkwood-lswxl.dts31
-rw-r--r--arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts1
-rw-r--r--arch/arm/boot/dts/logicpd-torpedo-som.dtsi9
-rw-r--r--arch/arm/boot/dts/omap5-board-common.dtsi33
-rw-r--r--arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts8
-rw-r--r--arch/arm/boot/dts/sama5d4.dtsi2
-rw-r--r--arch/arm/boot/dts/ste-nomadik-stn8815.dtsi37
-rw-r--r--arch/arm/configs/multi_v7_defconfig1
-rw-r--r--arch/arm/configs/omap2plus_defconfig10
-rw-r--r--arch/arm/mach-omap2/devices.c28
-rw-r--r--arch/arm/mach-omap2/pdata-quirks.c23
-rw-r--r--arch/arm/mach-omap2/sleep34xx.S61
-rw-r--r--arch/arm/mach-omap2/sleep44xx.S25
-rw-r--r--arch/arm/mach-realview/Kconfig3
-rw-r--r--arch/arm/mach-realview/platsmp-dt.c2
-rw-r--r--arch/arm/mach-tango/Kconfig3
-rw-r--r--arch/arm/mach-tango/platsmp.c2
-rw-r--r--arch/arm64/boot/dts/arm/juno-base.dtsi1
-rw-r--r--arch/arm64/boot/dts/nvidia/tegra132-norrin.dts2
-rw-r--r--drivers/bus/Kconfig2
-rw-r--r--drivers/bus/vexpress-config.c4
33 files changed, 230 insertions, 149 deletions
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 04885f9f959e..1fafaad516ba 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -439,6 +439,7 @@
ti,mbox-num-users = <4>;
ti,mbox-num-fifos = <8>;
mbox_wkupm3: wkup_m3 {
+ ti,mbox-send-noirq;
ti,mbox-tx = <0 0 0>;
ti,mbox-rx = <0 0 3>;
};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index df955ba4dc62..92068fbf8b57 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -73,7 +73,7 @@
global_timer: timer@48240200 {
compatible = "arm,cortex-a9-global-timer";
reg = <0x48240200 0x100>;
- interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&gic>;
clocks = <&mpu_periphclk>;
};
@@ -81,7 +81,7 @@
local_timer: timer@48240600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0x48240600 0x100>;
- interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&gic>;
clocks = <&mpu_periphclk>;
};
@@ -290,6 +290,7 @@
ti,mbox-num-users = <4>;
ti,mbox-num-fifos = <8>;
mbox_wkupm3: wkup_m3 {
+ ti,mbox-send-noirq;
ti,mbox-tx = <0 0 0>;
ti,mbox-rx = <0 0 3>;
};
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index 64d43325bcbc..ecd09ab6d581 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -590,8 +590,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pixcir_ts_pins>;
reg = <0x5c>;
- interrupt-parent = <&gpio3>;
- interrupts = <22 0>;
attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
@@ -599,7 +597,7 @@
* 0x264 represents the offset of padconf register of
* gpio3_22 from am43xx_pinmux base.
*/
- interrupts-extended = <&gpio3 22 IRQ_TYPE_NONE>,
+ interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>,
<&am43xx_pinmux 0x264>;
interrupt-names = "tsc", "wakeup";
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 746fd2b17958..d580e2b70f9a 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -491,7 +491,7 @@
pinctrl-0 = <&pixcir_ts_pins>;
reg = <0x5c>;
interrupt-parent = <&gpio1>;
- interrupts = <17 0>;
+ interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
index c53882643ae9..8d93882dc8d5 100644
--- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
+++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
@@ -167,7 +167,7 @@
DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */
DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */
DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLUP | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
+ DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
>;
};
@@ -492,14 +492,14 @@
pinctrl-names = "default";
pinctrl-0 = <&qspi1_pins>;
- spi-max-frequency = <20000000>;
+ spi-max-frequency = <48000000>;
spi_flash: spi_flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spansion,m25p80", "jedec,spi-nor";
reg = <0>; /* CS0 */
- spi-max-frequency = <20000000>;
+ spi-max-frequency = <48000000>;
partition@0 {
label = "uboot";
@@ -559,13 +559,13 @@
&cpsw_emac0 {
phy_id = <&davinci_mdio>, <0>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-txid";
dual_emac_res_vlan = <0>;
};
&cpsw_emac1 {
phy_id = <&davinci_mdio>, <1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-txid";
dual_emac_res_vlan = <1>;
};
@@ -588,7 +588,7 @@
};
&usb2 {
- dr_mode = "peripheral";
+ dr_mode = "host";
};
&mcasp3 {
diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts
index 77bb8e17401a..988e99632d49 100644
--- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts
+++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts
@@ -25,8 +25,8 @@
&dra7_pmx_core {
uart3_pins_default: uart3_pins_default {
pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
- DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
+ DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
+ DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
>;
};
@@ -108,9 +108,9 @@
pinctrl-0 = <&i2c5_pins_default>;
clock-frequency = <400000>;
- eeprom_base: atmel@50 {
+ eeprom_base: atmel@54 {
compatible = "atmel,24c08";
- reg = <0x50>;
+ reg = <0x54>;
pagesize = <16>;
};
diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
index 13cf69a8d0fb..fb9e1bbf2338 100644
--- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
+++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
@@ -152,6 +152,7 @@
nand-on-flash-bbt;
partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index 77ddff036409..e683856c507c 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -114,9 +114,15 @@
macb0: ethernet@f8008000 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_macb0_default>;
+ pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
phy-mode = "rmii";
status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioA>;
+ interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+ };
};
pdmic@f8018000 {
@@ -300,6 +306,10 @@
bias-disable;
};
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PC9__GPIO>;
+ };
+
pinctrl_pdmic_default: pdmic_default {
pinmux = <PIN_PB26__PDMIC_DAT>,
<PIN_PB27__PDMIC_CLK>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
index 131614f28e75..569026e8f96c 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -86,10 +86,12 @@
macb0: ethernet@f8020000 {
phy-mode = "rmii";
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
phy0: ethernet-phy@1 {
interrupt-parent = <&pioE>;
- interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
reg = <1>;
};
};
@@ -152,6 +154,10 @@
atmel,pins =
<AT91_PIOE 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
+ pinctrl_macb0_phy_irq: macb0_phy_irq_0 {
+ atmel,pins =
+ <AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
};
};
};
diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts
index 2d4a33100af6..4e98cda97403 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d4ek.dts
@@ -160,8 +160,15 @@
};
macb0: ethernet@f8020000 {
+ pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
phy-mode = "rmii";
status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioE>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ };
};
mmc1: mmc@fc000000 {
@@ -193,6 +200,10 @@
pinctrl@fc06a000 {
board {
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ atmel,pins =
+ <AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
pinctrl_mmc0_cd: mmc0_cd {
atmel,pins =
<AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index ca4ddf86817a..626c67d66626 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -215,7 +215,7 @@
};
panel: panel {
- compatible = "qd,qd43003c0-40", "simple-panel";
+ compatible = "qiaodian,qd43003c0-40", "simple-panel";
backlight = <&backlight>;
power-supply = <&panel_reg>;
#address-cells = <1>;
diff --git a/arch/arm/boot/dts/kirkwood-lswvl.dts b/arch/arm/boot/dts/kirkwood-lswvl.dts
index 09eed3cea0af..36eec7392ab4 100644
--- a/arch/arm/boot/dts/kirkwood-lswvl.dts
+++ b/arch/arm/boot/dts/kirkwood-lswvl.dts
@@ -1,7 +1,8 @@
/*
* Device Tree file for Buffalo Linkstation LS-WVL/VL
*
- * Copyright (C) 2015, rogershimizu@gmail.com
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -156,21 +157,21 @@
button@1 {
label = "Function Button";
linux,code = <KEY_OPTION>;
- gpios = <&gpio0 45 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
};
button@2 {
label = "Power-on Switch";
linux,code = <KEY_RESERVED>;
linux,input-type = <5>;
- gpios = <&gpio0 46 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
};
button@3 {
label = "Power-auto Switch";
linux,code = <KEY_ESC>;
linux,input-type = <5>;
- gpios = <&gpio0 47 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
};
};
@@ -185,38 +186,38 @@
led@1 {
label = "lswvl:red:alarm";
- gpios = <&gpio0 36 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
};
led@2 {
label = "lswvl:red:func";
- gpios = <&gpio0 37 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
};
led@3 {
label = "lswvl:amber:info";
- gpios = <&gpio0 38 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
};
led@4 {
label = "lswvl:blue:func";
- gpios = <&gpio0 39 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
};
led@5 {
label = "lswvl:blue:power";
- gpios = <&gpio0 40 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
led@6 {
label = "lswvl:red:hdderr0";
- gpios = <&gpio0 34 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
};
led@7 {
label = "lswvl:red:hdderr1";
- gpios = <&gpio0 35 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
};
};
@@ -233,7 +234,7 @@
3250 1
5000 0>;
- alarm-gpios = <&gpio0 43 GPIO_ACTIVE_HIGH>;
+ alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
};
restart_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-lswxl.dts b/arch/arm/boot/dts/kirkwood-lswxl.dts
index f5db16a08597..b13ec20a7088 100644
--- a/arch/arm/boot/dts/kirkwood-lswxl.dts
+++ b/arch/arm/boot/dts/kirkwood-lswxl.dts
@@ -1,7 +1,8 @@
/*
* Device Tree file for Buffalo Linkstation LS-WXL/WSXL
*
- * Copyright (C) 2015, rogershimizu@gmail.com
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
@@ -156,21 +157,21 @@
button@1 {
label = "Function Button";
linux,code = <KEY_OPTION>;
- gpios = <&gpio1 41 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
};
button@2 {
label = "Power-on Switch";
linux,code = <KEY_RESERVED>;
linux,input-type = <5>;
- gpios = <&gpio1 42 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
};
button@3 {
label = "Power-auto Switch";
linux,code = <KEY_ESC>;
linux,input-type = <5>;
- gpios = <&gpio1 43 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
};
};
@@ -185,12 +186,12 @@
led@1 {
label = "lswxl:blue:func";
- gpios = <&gpio1 36 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
};
led@2 {
label = "lswxl:red:alarm";
- gpios = <&gpio1 49 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
};
led@3 {
@@ -200,23 +201,23 @@
led@4 {
label = "lswxl:blue:power";
- gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
};
led@5 {
label = "lswxl:red:func";
- gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
- default-state = "keep";
+ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
};
led@6 {
label = "lswxl:red:hdderr0";
- gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
};
led@7 {
label = "lswxl:red:hdderr1";
- gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
};
};
@@ -225,15 +226,15 @@
pinctrl-0 = <&pmx_fan_low &pmx_fan_high &pmx_fan_lock>;
pinctrl-names = "default";
- gpios = <&gpio0 47 GPIO_ACTIVE_LOW
- &gpio0 48 GPIO_ACTIVE_LOW>;
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW
+ &gpio1 15 GPIO_ACTIVE_LOW>;
gpio-fan,speed-map = <0 3
1500 2
3250 1
5000 0>;
- alarm-gpios = <&gpio1 49 GPIO_ACTIVE_HIGH>;
+ alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
};
restart_poweroff {
@@ -256,7 +257,7 @@
enable-active-high;
regulator-always-on;
regulator-boot-on;
- gpio = <&gpio0 37 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
};
hdd_power0: regulator@2 {
compatible = "regulator-fixed";
diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
index 1db6f2c506cc..8082d64266a3 100644
--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
+++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
@@ -131,6 +131,7 @@
chip-delay = <40>;
status = "okay";
partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
index 7fed0bd4f3de..00805322367e 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
+++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
@@ -112,14 +112,6 @@
clock-frequency = <400000>;
};
-&i2c2 {
- clock-frequency = <400000>;
-};
-
-&i2c3 {
- clock-frequency = <400000>;
-};
-
/*
* Only found on the wireless SOM. For the SOM without wireless, the pins for
* MMC3 can be routed with jumpers to the second MMC slot on the devkit and
@@ -143,6 +135,7 @@
interrupt-parent = <&gpio5>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
ref-clock-frequency = <26000000>;
+ tcxo-clock-frequency = <26000000>;
};
};
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi
index 888412c63f97..902657d6713b 100644
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -130,6 +130,16 @@
};
};
+&gpio8 {
+ /* TI trees use GPIO instead of msecure, see also muxing */
+ p234 {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "gpio8_234/msecure";
+ };
+};
+
&omap5_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
@@ -213,6 +223,13 @@
>;
};
+ /* TI trees use GPIO mode; msecure mode does not work reliably? */
+ palmas_msecure_pins: palmas_msecure_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */
+ >;
+ };
+
usbhost_pins: pinmux_usbhost_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
@@ -278,6 +295,12 @@
&usbhost_wkup_pins
>;
+ palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */
+ >;
+ };
+
usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
@@ -345,6 +368,8 @@
interrupt-controller;
#interrupt-cells = <2>;
ti,system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
extcon_usb3: palmas_usb {
compatible = "ti,palmas-usb-vid";
@@ -358,6 +383,14 @@
#clock-cells = <0>;
};
+ rtc {
+ compatible = "ti,palmas-rtc";
+ interrupt-parent = <&palmas>;
+ interrupts = <8 IRQ_TYPE_NONE>;
+ ti,backup-battery-chargeable;
+ ti,backup-battery-charge-high-current;
+ };
+
palmas_pmic {
compatible = "ti,palmas-pmic";
interrupt-parent = <&palmas>;
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts b/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
index 3daec912b4bf..420788229e6f 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
+++ b/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
@@ -1,7 +1,8 @@
/*
* Device Tree file for Buffalo Linkstation LS-WTGL
*
- * Copyright (C) 2015, Roger Shimizu <rogershimizu@gmail.com>
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -69,8 +70,6 @@
internal-regs {
pinctrl: pinctrl@10000 {
- pinctrl-0 = <&pmx_usb_power &pmx_power_hdd
- &pmx_fan_low &pmx_fan_high &pmx_fan_lock>;
pinctrl-names = "default";
pmx_led_power: pmx-leds {
@@ -162,6 +161,7 @@
led@1 {
label = "lswtgl:blue:power";
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
};
led@2 {
@@ -188,7 +188,7 @@
3250 1
5000 0>;
- alarm-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+ alarm-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
};
restart_poweroff {
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index b8032bca4621..db1151c18466 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -1342,7 +1342,7 @@
dbgu: serial@fc069000 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfc069000 0x200>;
- interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
+ interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
clocks = <&dbgu_clk>;
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
index d0c743853318..27a333eb8987 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
@@ -127,22 +127,14 @@
};
mmcsd_default_mode: mmcsd_default {
mmcsd_default_cfg1 {
- /* MCCLK */
- pins = "GPIO8_B10";
- ste,output = <0>;
- };
- mmcsd_default_cfg2 {
- /* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */
- pins = "GPIO10_C11", "GPIO15_A12",
- "GPIO16_C13", "GPIO23_D15";
- ste,output = <1>;
- };
- mmcsd_default_cfg3 {
- /* MCCMD, MCDAT3-0, MCMSFBCLK */
- pins = "GPIO9_A10", "GPIO11_B11",
- "GPIO12_A11", "GPIO13_C12",
- "GPIO14_B12", "GPIO24_C15";
- ste,input = <1>;
+ /*
+ * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2
+ * MCCMD, MCDAT3-0, MCMSFBCLK
+ */
+ pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11",
+ "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12",
+ "GPIO16_C13", "GPIO23_D15", "GPIO24_C15";
+ ste,output = <2>;
};
};
};
@@ -802,10 +794,21 @@
clock-names = "mclk", "apb_pclk";
interrupt-parent = <&vica>;
interrupts = <22>;
- max-frequency = <48000000>;
+ max-frequency = <400000>;
bus-width = <4>;
cap-mmc-highspeed;
cap-sd-highspeed;
+ full-pwr-cycle;
+ /*
+ * The STw4811 circuit used with the Nomadik strictly
+ * requires that all of these signal direction pins be
+ * routed and used for its 4-bit levelshifter.
+ */
+ st,sig-dir-dat0;
+ st,sig-dir-dat2;
+ st,sig-dir-dat31;
+ st,sig-dir-cmd;
+ st,sig-pin-fbclk;
pinctrl-names = "default";
pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
vmmc-supply = <&vmmc_regulator>;
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 314f6be2dca2..8e8b2ace9b7c 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -426,6 +426,7 @@ CONFIG_SUNXI_WATCHDOG=y
CONFIG_IMX2_WDT=y
CONFIG_TEGRA_WATCHDOG=m
CONFIG_MESON_WATCHDOG=y
+CONFIG_DW_WATCHDOG=y
CONFIG_DIGICOLOR_WATCHDOG=y
CONFIG_MFD_AS3711=y
CONFIG_MFD_AS3722=y
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index c5e1943e5427..a7151744b85c 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -50,6 +50,7 @@ CONFIG_SOC_AM33XX=y
CONFIG_SOC_AM43XX=y
CONFIG_SOC_DRA7XX=y
CONFIG_ARM_THUMBEE=y
+CONFIG_ARM_KERNMEM_PERMS=y
CONFIG_ARM_ERRATA_411920=y
CONFIG_ARM_ERRATA_430973=y
CONFIG_SMP=y
@@ -177,6 +178,7 @@ CONFIG_TI_CPTS=y
CONFIG_AT803X_PHY=y
CONFIG_SMSC_PHY=y
CONFIG_USB_USBNET=m
+CONFIG_USB_NET_SMSC75XX=m
CONFIG_USB_NET_SMSC95XX=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
@@ -354,6 +356,11 @@ CONFIG_USB_MUSB_DSPS=m
CONFIG_USB_INVENTRA_DMA=y
CONFIG_USB_TI_CPPI41_DMA=y
CONFIG_USB_DWC3=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_SIMPLE=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_TEST=m
CONFIG_AM335X_PHY_USB=y
CONFIG_USB_GADGET=m
@@ -387,6 +394,7 @@ CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m
CONFIG_LEDS_GPIO=m
CONFIG_LEDS_PWM=m
+CONFIG_LEDS_PCA963X=m
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_ONESHOT=m
@@ -449,6 +457,8 @@ CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_SPLIT=y
+CONFIG_DEBUG_INFO_DWARF4=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 9cda974a3009..d7f1d69daf6d 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -18,7 +18,6 @@
#include <linux/slab.h>
#include <linux/of.h>
#include <linux/pinctrl/machine.h>
-#include <linux/platform_data/mailbox-omap.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
@@ -66,32 +65,6 @@ static int __init omap3_l3_init(void)
}
omap_postcore_initcall(omap3_l3_init);
-#if defined(CONFIG_OMAP2PLUS_MBOX) || defined(CONFIG_OMAP2PLUS_MBOX_MODULE)
-static inline void __init omap_init_mbox(void)
-{
- struct omap_hwmod *oh;
- struct platform_device *pdev;
- struct omap_mbox_pdata *pdata;
-
- oh = omap_hwmod_lookup("mailbox");
- if (!oh) {
- pr_err("%s: unable to find hwmod\n", __func__);
- return;
- }
- if (!oh->dev_attr) {
- pr_err("%s: hwmod doesn't have valid attrs\n", __func__);
- return;
- }
-
- pdata = (struct omap_mbox_pdata *)oh->dev_attr;
- pdev = omap_device_build("omap-mailbox", -1, oh, pdata, sizeof(*pdata));
- WARN(IS_ERR(pdev), "%s: could not build device, err %ld\n",
- __func__, PTR_ERR(pdev));
-}
-#else
-static inline void omap_init_mbox(void) { }
-#endif /* CONFIG_OMAP2PLUS_MBOX */
-
static inline void omap_init_sti(void) {}
#if defined(CONFIG_SPI_OMAP24XX) || defined(CONFIG_SPI_OMAP24XX_MODULE)
@@ -229,7 +202,6 @@ static int __init omap2_init_devices(void)
* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
- omap_init_mbox();
omap_init_mcspi();
omap_init_sham();
omap_init_aes();
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index e781e4fae13a..a935d28443da 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -23,6 +23,8 @@
#include <linux/platform_data/pinctrl-single.h>
#include <linux/platform_data/iommu-omap.h>
#include <linux/platform_data/wkup_m3.h>
+#include <linux/platform_data/pwm_omap_dmtimer.h>
+#include <plat/dmtimer.h>
#include "common.h"
#include "common-board-devices.h"
@@ -449,6 +451,24 @@ void omap_auxdata_legacy_init(struct device *dev)
dev->platform_data = &twl_gpio_auxdata;
}
+/* Dual mode timer PWM callbacks platdata */
+#if IS_ENABLED(CONFIG_OMAP_DM_TIMER)
+struct pwm_omap_dmtimer_pdata pwm_dmtimer_pdata = {
+ .request_by_node = omap_dm_timer_request_by_node,
+ .free = omap_dm_timer_free,
+ .enable = omap_dm_timer_enable,
+ .disable = omap_dm_timer_disable,
+ .get_fclk = omap_dm_timer_get_fclk,
+ .start = omap_dm_timer_start,
+ .stop = omap_dm_timer_stop,
+ .set_load = omap_dm_timer_set_load,
+ .set_match = omap_dm_timer_set_match,
+ .set_pwm = omap_dm_timer_set_pwm,
+ .set_prescaler = omap_dm_timer_set_prescaler,
+ .write_counter = omap_dm_timer_write_counter,
+};
+#endif
+
/*
* Few boards still need auxdata populated before we populate
* the dev entries in of_platform_populate().
@@ -502,6 +522,9 @@ static struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
OF_DEV_AUXDATA("ti,am4372-wkup-m3", 0x44d00000, "44d00000.wkup_m3",
&wkup_m3_data),
#endif
+#if IS_ENABLED(CONFIG_OMAP_DM_TIMER)
+ OF_DEV_AUXDATA("ti,omap-dmtimer-pwm", 0, NULL, &pwm_dmtimer_pdata),
+#endif
#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
OF_DEV_AUXDATA("ti,omap4-iommu", 0x4a066000, "4a066000.mmu",
&omap4_iommu_pdata),
diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S
index eafd120b53f1..1b9f0520dea9 100644
--- a/arch/arm/mach-omap2/sleep34xx.S
+++ b/arch/arm/mach-omap2/sleep34xx.S
@@ -86,13 +86,18 @@ ENTRY(enable_omap3630_toggle_l2_on_restore)
stmfd sp!, {lr} @ save registers on stack
/* Setup so that we will disable and enable l2 */
mov r1, #0x1
- adrl r2, l2dis_3630 @ may be too distant for plain adr
- str r1, [r2]
+ adrl r3, l2dis_3630_offset @ may be too distant for plain adr
+ ldr r2, [r3] @ value for offset
+ str r1, [r2, r3] @ write to l2dis_3630
ldmfd sp!, {pc} @ restore regs and return
ENDPROC(enable_omap3630_toggle_l2_on_restore)
- .text
-/* Function to call rom code to save secure ram context */
+/*
+ * Function to call rom code to save secure ram context. This gets
+ * relocated to SRAM, so it can be all in .data section. Otherwise
+ * we need to initialize api_params separately.
+ */
+ .data
.align 3
ENTRY(save_secure_ram_context)
stmfd sp!, {r4 - r11, lr} @ save registers on stack
@@ -126,6 +131,8 @@ ENDPROC(save_secure_ram_context)
ENTRY(save_secure_ram_context_sz)
.word . - save_secure_ram_context
+ .text
+
/*
* ======================
* == Idle entry point ==
@@ -289,12 +296,6 @@ wait_sdrc_ready:
bic r5, r5, #0x40
str r5, [r4]
-/*
- * PC-relative stores lead to undefined behaviour in Thumb-2: use a r7 as a
- * base instead.
- * Be careful not to clobber r7 when maintaing this code.
- */
-
is_dll_in_lock_mode:
/* Is dll in lock mode? */
ldr r4, sdrc_dlla_ctrl
@@ -302,11 +303,7 @@ is_dll_in_lock_mode:
tst r5, #0x4
bne exit_nonoff_modes @ Return if locked
/* wait till dll locks */
- adr r7, kick_counter
wait_dll_lock_timed:
- ldr r4, wait_dll_lock_counter
- add r4, r4, #1
- str r4, [r7, #wait_dll_lock_counter - kick_counter]
ldr r4, sdrc_dlla_status
/* Wait 20uS for lock */
mov r6, #8
@@ -330,9 +327,6 @@ kick_dll:
orr r6, r6, #(1<<3) @ enable dll
str r6, [r4]
dsb
- ldr r4, kick_counter
- add r4, r4, #1
- str r4, [r7] @ kick_counter
b wait_dll_lock_timed
exit_nonoff_modes:
@@ -360,15 +354,6 @@ sdrc_dlla_status:
.word SDRC_DLLA_STATUS_V
sdrc_dlla_ctrl:
.word SDRC_DLLA_CTRL_V
- /*
- * When exporting to userspace while the counters are in SRAM,
- * these 2 words need to be at the end to facilitate retrival!
- */
-kick_counter:
- .word 0
-wait_dll_lock_counter:
- .word 0
-
ENTRY(omap3_do_wfi_sz)
.word . - omap3_do_wfi
@@ -437,7 +422,9 @@ ENTRY(omap3_restore)
cmp r2, #0x0 @ Check if target power state was OFF or RET
bne logic_l1_restore
- ldr r0, l2dis_3630
+ adr r1, l2dis_3630_offset @ address for offset
+ ldr r0, [r1] @ value for offset
+ ldr r0, [r1, r0] @ value at l2dis_3630
cmp r0, #0x1 @ should we disable L2 on 3630?
bne skipl2dis
mrc p15, 0, r0, c1, c0, 1
@@ -449,12 +436,14 @@ skipl2dis:
and r1, #0x700
cmp r1, #0x300
beq l2_inv_gp
+ adr r0, l2_inv_api_params_offset
+ ldr r3, [r0]
+ add r3, r3, r0 @ r3 points to dummy parameters
mov r0, #40 @ set service ID for PPA
mov r12, r0 @ copy secure Service ID in r12
mov r1, #0 @ set task id for ROM code in r1
mov r2, #4 @ set some flags in r2, r6
mov r6, #0xff
- adr r3, l2_inv_api_params @ r3 points to dummy parameters
dsb @ data write barrier
dmb @ data memory barrier
smc #1 @ call SMI monitor (smi #1)
@@ -488,8 +477,8 @@ skipl2dis:
b logic_l1_restore
.align
-l2_inv_api_params:
- .word 0x1, 0x00
+l2_inv_api_params_offset:
+ .long l2_inv_api_params - .
l2_inv_gp:
/* Execute smi to invalidate L2 cache */
mov r12, #0x1 @ set up to invalidate L2
@@ -506,7 +495,9 @@ l2_inv_gp:
mov r12, #0x2
smc #0 @ Call SMI monitor (smieq)
logic_l1_restore:
- ldr r1, l2dis_3630
+ adr r0, l2dis_3630_offset @ adress for offset
+ ldr r1, [r0] @ value for offset
+ ldr r1, [r0, r1] @ value at l2dis_3630
cmp r1, #0x1 @ Test if L2 re-enable needed on 3630
bne skipl2reen
mrc p15, 0, r1, c1, c0, 1
@@ -535,9 +526,17 @@ control_stat:
.word CONTROL_STAT
control_mem_rta:
.word CONTROL_MEM_RTA_CTRL
+l2dis_3630_offset:
+ .long l2dis_3630 - .
+
+ .data
l2dis_3630:
.word 0
+ .data
+l2_inv_api_params:
+ .word 0x1, 0x00
+
/*
* Internal functions
*/
diff --git a/arch/arm/mach-omap2/sleep44xx.S b/arch/arm/mach-omap2/sleep44xx.S
index 9b09d85d811a..c7a3b4aab4b5 100644
--- a/arch/arm/mach-omap2/sleep44xx.S
+++ b/arch/arm/mach-omap2/sleep44xx.S
@@ -29,12 +29,6 @@
dsb
.endm
-ppa_zero_params:
- .word 0x0
-
-ppa_por_params:
- .word 1, 0
-
#ifdef CONFIG_ARCH_OMAP4
/*
@@ -266,7 +260,9 @@ ENTRY(omap4_cpu_resume)
beq skip_ns_smp_enable
ppa_actrl_retry:
mov r0, #OMAP4_PPA_CPU_ACTRL_SMP_INDEX
- adr r3, ppa_zero_params @ Pointer to parameters
+ adr r1, ppa_zero_params_offset
+ ldr r3, [r1]
+ add r3, r3, r1 @ Pointer to ppa_zero_params
mov r1, #0x0 @ Process ID
mov r2, #0x4 @ Flag
mov r6, #0xff
@@ -303,7 +299,9 @@ skip_ns_smp_enable:
ldr r0, =OMAP4_PPA_L2_POR_INDEX
ldr r1, =OMAP44XX_SAR_RAM_BASE
ldr r4, [r1, #L2X0_PREFETCH_CTRL_OFFSET]
- adr r3, ppa_por_params
+ adr r1, ppa_por_params_offset
+ ldr r3, [r1]
+ add r3, r3, r1 @ Pointer to ppa_por_params
str r4, [r3, #0x04]
mov r1, #0x0 @ Process ID
mov r2, #0x4 @ Flag
@@ -328,6 +326,8 @@ skip_l2en:
#endif
b cpu_resume @ Jump to generic resume
+ppa_por_params_offset:
+ .long ppa_por_params - .
ENDPROC(omap4_cpu_resume)
#endif /* CONFIG_ARCH_OMAP4 */
@@ -380,4 +380,13 @@ ENTRY(omap_do_wfi)
nop
ldmfd sp!, {pc}
+ppa_zero_params_offset:
+ .long ppa_zero_params - .
ENDPROC(omap_do_wfi)
+
+ .data
+ppa_zero_params:
+ .word 0
+
+ppa_por_params:
+ .word 1, 0
diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig
index def40a0dd60c..70ab4a25a5f8 100644
--- a/arch/arm/mach-realview/Kconfig
+++ b/arch/arm/mach-realview/Kconfig
@@ -1,5 +1,6 @@
menuconfig ARCH_REALVIEW
- bool "ARM Ltd. RealView family" if ARCH_MULTI_V5 || ARCH_MULTI_V6 || ARCH_MULTI_V7
+ bool "ARM Ltd. RealView family"
+ depends on ARCH_MULTI_V5 || ARCH_MULTI_V6 || ARCH_MULTI_V7
select ARM_AMBA
select ARM_TIMER_SP804
select COMMON_CLK_VERSATILE
diff --git a/arch/arm/mach-realview/platsmp-dt.c b/arch/arm/mach-realview/platsmp-dt.c
index 65585392655b..6964e8876061 100644
--- a/arch/arm/mach-realview/platsmp-dt.c
+++ b/arch/arm/mach-realview/platsmp-dt.c
@@ -80,7 +80,7 @@ static void __init realview_smp_prepare_cpus(unsigned int max_cpus)
virt_to_phys(versatile_secondary_startup));
}
-struct smp_operations realview_dt_smp_ops __initdata = {
+static const struct smp_operations realview_dt_smp_ops __initconst = {
.smp_prepare_cpus = realview_smp_prepare_cpus,
.smp_secondary_init = versatile_secondary_init,
.smp_boot_secondary = versatile_boot_secondary,
diff --git a/arch/arm/mach-tango/Kconfig b/arch/arm/mach-tango/Kconfig
index d6a3714b096e..ebe15b93bbe8 100644
--- a/arch/arm/mach-tango/Kconfig
+++ b/arch/arm/mach-tango/Kconfig
@@ -1,5 +1,6 @@
config ARCH_TANGO
- bool "Sigma Designs Tango4 (SMP87xx)" if ARCH_MULTI_V7
+ bool "Sigma Designs Tango4 (SMP87xx)"
+ depends on ARCH_MULTI_V7
# Cortex-A9 MPCore r3p0, PL310 r3p2
select ARCH_HAS_HOLES_MEMORYMODEL
select ARM_ERRATA_754322
diff --git a/arch/arm/mach-tango/platsmp.c b/arch/arm/mach-tango/platsmp.c
index a18d5a34e2f5..a21f55e000d2 100644
--- a/arch/arm/mach-tango/platsmp.c
+++ b/arch/arm/mach-tango/platsmp.c
@@ -9,7 +9,7 @@ static int tango_boot_secondary(unsigned int cpu, struct task_struct *idle)
return 0;
}
-static struct smp_operations tango_smp_ops __initdata = {
+static const struct smp_operations tango_smp_ops __initconst = {
.smp_boot_secondary = tango_boot_secondary,
};
diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi
index dd5158eb5872..e5b59ca9debb 100644
--- a/arch/arm64/boot/dts/arm/juno-base.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-base.dtsi
@@ -115,6 +115,7 @@
<GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
diff --git a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
index 7dfe1c085966..62f33fc84e3e 100644
--- a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
@@ -12,6 +12,8 @@
rtc1 = "/rtc@0,7000e000";
};
+ chosen { };
+
memory {
device_type = "memory";
reg = <0x0 0x80000000 0x0 0x80000000>;
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 129d47bcc5fc..9a92c072a485 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -132,7 +132,7 @@ config SUNXI_RSB
and AC100/AC200 ICs.
config UNIPHIER_SYSTEM_BUS
- bool "UniPhier System Bus driver"
+ tristate "UniPhier System Bus driver"
depends on ARCH_UNIPHIER && OF
default y
help
diff --git a/drivers/bus/vexpress-config.c b/drivers/bus/vexpress-config.c
index 6575c0fe6a4e..c3cb76b363c6 100644
--- a/drivers/bus/vexpress-config.c
+++ b/drivers/bus/vexpress-config.c
@@ -192,8 +192,10 @@ static int __init vexpress_config_init(void)
/* Need the config devices early, before the "normal" devices... */
for_each_compatible_node(node, NULL, "arm,vexpress,config-bus") {
err = vexpress_config_populate(node);
- if (err)
+ if (err) {
+ of_node_put(node);
break;
+ }
}
return err;